|
|
|
Compression Molding Showroom
Welcome to Greenerd's Compression Molding Applications Showroom.
We design and build robust equipment intended for maximum up-time in demanding production environments.
No matter where your operations are located, we want to help you to compete with reliable
equipment and intelligent controls.
We can incorporate a Greenerd Electronic Press Control into any of our hydraulic presses.
Just imagine how the following control functions can improve productivity in your compression
molding operation:
- Provide feedback of most press functions, including ram speed, dwell time, operating
pressures, distances traveled and other process parameters
- Perform data acquisition and automate SPC reporting
- Actuate any operation internal or external to the die, such as those utilizing eject
pins, knockouts, or punches
- Provide remote communications from your process via, Intra-net, Internet, or dial-up
modem. This capability can be harnessed for press monitoring, remote diagnostics, and
trouble-shooting by experienced Greenerd service personnel.
Call the Greenerd Sales staff at 1-800-877-9110 (within the US) or 1-603-889-4101 (outside the US)
to discuss your compression molding requirements and discover how easy it is to put our experience
to work for you!
If you have interest in a specific application or if you don't see what you are looking for, please contact us.
E-mail
RFQ Form
|
 |
|
4D-400-86X40-21R24
This pair of 400 ton presses is used to mold SMC into electrical cabinets. Electronic speed control allows for an adjustable
pressing speed as well as intermediate and rapid close and open speeds. The Greenerd Press Control allows for both press and
mold functions to be programmed and stored. Typical mold functions include initiation and pressure setting for hydraulic
actuators within the mold.
Contact Applications Engineering for more information.
E-mail
RFQ Form
|
4D-600-120x36-38R
Built for the same process and customer as the 4D-300 below, this press molds SMC
into components for the industrial lighting industry. This customer is running their
three large, compression molding presses from Greenerd two shifts per day, six days per
week.
Contact Applications Engineering for more information.
E-mail
RFQ Form
|
|
 |
 |
|
CPA-50
Hydrolair air over oil presses, available in 5 tonnage ranges, from 30 tons to 250
tons. The Hydrolair 4-post, up acting, air over oil presses will hold a vice-like grip
for seconds, minutes, or hours, maintaining tonnage for virtually any length of time.
With low initial cost and minimal operating costs, the Hydrolair line of presses offers
the force of a conventional hydraulic press at a fraction of the cost.
Contact Applications Engineering for more information.
E-mail
RFQ Form
|
4U-120-42x42-25R3
A 120 ton up-acting press for forming polishing pads for the semiconductor industry.
Bed size is 42" x 42". Electric heated platens are controlled to 375°
F through the Touchscreen control with temperature feedback from six thermo-couples.
Contact Applications Engineering for more information.
E-mail
RFQ Form
|
|
 |
 |
|
4D-50-110x84-15R3
This 50 ton press has a large bed (110" x 84") for forming automotive heat
shields and acoustical panels. The press can accommodate die sets weighing up to
12,000# with integrated QDC equipment. Operator touchscreen interface is built
into the fully portable, integrated hydraulic power unit and electrical console.
Contact Applications Engineering for more information.
E-mail
RFQ Form
|
4D-300-72x36-19R
This 300 ton press utilizes a pre-fill hydraulic system to provide rapid advance
and return speeds of 700+ ipm for the large platen. The press' industrial computer controls
in-die process parameters as well as press performance. Ethernet connectivity enables
Greenerd to monitor press performance from 2000 miles away. We helped this customer to
increase output by 33% within the first 30 days after installation.
Contact Applications Engineering for more information.
E-mail
RFQ Form
|
|
 |
 |
|
GG-400-84x84
This unique press is used to mold metal tape under an extensive dwell and pressure
cycle. The 400 ton Gib-guided design will withstand an extreme, off-center load of up
to 200 tons 33" off-center while maintaining parallelism of 0.015". This press
is used to produce a mission-critical component for a military defense contractor.
Greenerd was one of only two builders that would quote these extreme specifications.
Contact Applications Engineering for more information.
E-mail
RFQ Form
|
Call the Greenerd Sales staff at 1-800-877-9110 (within the US) or 1-603-889-4101 (outside the
US) to discuss your compression molding requirements and discover how easy it is to put
our experience to work for you!
We can incorporate a Greenerd Electronic Press Control into any of our hydraulic presses.
Just imagine how the following control functions can improve productivity in your compression
molding operation:
- Provide feedback of most press functions, including ram speed, dwell time, operating
pressures, distances traveled and other process parameters
- Perform data acquisition and automate SPC reporting
- Actuate any operation internal or external to the die, such as those utilizing eject
pins, knockouts, or punches
- Provide remote communications from your process via, Intra-net, Internet, or dial-up
modem. This capability can be harnessed for press monitoring, remote diagnostics, and
trouble-shooting by experienced Greenerd service personnel.
Call the Greenerd Sales staff at 1-800-877-9110 (within the US) or 1-603-889-4101 (outside the US)
to discuss your compression molding requirements and discover how easy it is to put our experience
to work for you!
|
|
|
|
|
